Breaking for Spares Fiat Scudo Taxi

goody33 · 2016-02-08 03:20:40

I have a 2003 Fiat Scudo taxi that I bought for some bits and now the rest is surplus to requirement.
The slide doors, headlining, interior plastic wheel arch trim, heater controls and engine are not available, but the rest is pretty much there.

PM me with any requests.

http://www.ebay.co.uk/itm/231833802506? … 1555.l2649

Thanks,

Phil.

Casper · 2016-02-10 16:00:50

How is that back door seal Phil? I also need the one that runs along the top back. It almost hangs over the doors when shut. Mine is split and green with mold.

Cheers

R

goody33 · 2016-02-10 17:17:29

It seems ok, but it was a bit dark when I checked. I will get the heater controls out soon. Ive not be well and the control needed the centre taxi control unit taking out, which needed the drivers seat taking out. The drivers seat is out now, so I will get the controls out over the weekend.

Casper · 2016-02-10 18:25:41

The one along the top. It looks like screwed in and screws covered with a plastic cap. I could me wrong and it just be plastic pop ins but either way. No need to try and save the fittings.

goody33 · 2016-02-13 15:41:43

Casper, I've have taken a photo of the back door seal. Is this the one you want?
If not, send me a picture of the one you need and I will check the van.
I have taken the heater control unit out of the van now, so if you still want it, its yours.

Last edited by goody33 (2016-02-13 15:42:48)

Casper · 2016-02-13 18:12:15

goody33 wrote:

Casper, I've have taken a photo of the back door seal. Is this the one you want?
If not, send me a picture of the one you need and I will check the van.
I have taken the heater control unit out of the van now, so if you still want it, its yours.
http://dispatchexpertscudo.org.uk/forum/img/members/383/mini_WP_20160213_001.jpeg

Yes that and the one that runs along the top of the back doors if its not split. Not sure if screwed or popped in place. Mine is well shot. Did you manage to test the heater? Im sure it will be fine. Just box them up mate and PM me you paypal address and ill PM back my post address.

goody33 · 2016-02-13 18:41:20

The rubber seal sits over a lip around the aperture of the back doors.
I did test the heater and it all seems ok. Did you want the control panel from the front? I will only dispose of it otherwise.

Casper · 2016-02-13 19:02:20

Wonder if they done away with it on the later models. Part 13 on this ....

http://ebayapi.loc8apartltd.netdna-cdn. … 0P/$_1.JPG

I seen an after market one for around £20 so ill see how i get on after that one before getting a new top one. Yeah i may as well take the panel. Mine looks old anyway. People with rings by the looks of it.

Casper · 2016-02-13 19:09:42

Check your email and paypal. That should be you sorted if i did it correct big_smile

Casper · 2016-02-22 14:21:39

Cheers Phil. Bits came today. Dont think the air con bit matters. I have a two position slider that i never use anyway. Heat and speed is the same and the other never leaves the screen position. Sunny day so i may fit that later.

Ta. smile

Casper · 2016-02-22 20:58:32

Casper wrote:

Cheers Phil. Bits came today. Dont think the air con bit matters. I have a two position slider that i never use anyway. Heat and speed is the same and the other never leaves the screen position. Sunny day so i may fit that later.
Ta.

It did matter. Air con one does not fit. Well it does but the block connector for the non air con one only has about four wires in use on a block of six. The air con wire block has about 20 pins however not all was lost. Stripped down the two units and made one good one as mine had pins missing for the slider buttons. All i need to do now is sus why i can no speed adjustment. Must have put something back wrong. Luck i have not put the dash back on yet. Christ what a job for such a small part yikes

goody33 · 2016-02-23 19:15:10

Hope you got it sorted.

goody33 · 2016-02-23 19:17:52

Last call for any parts on the van before it gets scrapped at the weekend.

Casper · 2016-02-23 19:25:42

goody33 wrote:

Hope you got it sorted.

Yeah. Little brass spring needed for to make contact had fell off. Once back on its fine. Managed to get all the screws back in the original holes as well what is quite good for me big_smile

The Dispatch | Expert | Scudo Hub

Get help & share your Citroen Dispatch (Jumpy) | Peugeot Expert | Fiat Scudo tips

#1 2016-02-08 03:20:40

Breaking for Spares Fiat Scudo Taxi

#2 2016-02-10 16:00:50

Re: Breaking for Spares Fiat Scudo Taxi

#3 2016-02-10 17:17:29

Re: Breaking for Spares Fiat Scudo Taxi

#4 2016-02-10 18:25:41

Re: Breaking for Spares Fiat Scudo Taxi

#5 2016-02-13 15:41:43

Re: Breaking for Spares Fiat Scudo Taxi

#6 2016-02-13 18:12:15

Re: Breaking for Spares Fiat Scudo Taxi

#7 2016-02-13 18:41:20

Re: Breaking for Spares Fiat Scudo Taxi

#8 2016-02-13 19:02:20

Re: Breaking for Spares Fiat Scudo Taxi

#9 2016-02-13 19:09:42

Re: Breaking for Spares Fiat Scudo Taxi

#10 2016-02-22 14:21:39

Re: Breaking for Spares Fiat Scudo Taxi

#11 2016-02-22 20:58:32

Re: Breaking for Spares Fiat Scudo Taxi

#12 2016-02-23 19:15:10

Re: Breaking for Spares Fiat Scudo Taxi

#13 2016-02-23 19:17:52

Re: Breaking for Spares Fiat Scudo Taxi

#14 2016-02-23 19:25:42

Re: Breaking for Spares Fiat Scudo Taxi

Board footer